Group Instrumentation

Leading Technology for Emission Monitoring and Process Control
< Home | Our Products > Dust / Particulate Monitoring > Electrodynamic Probe Technology

Electrodynamic Probe Technology

PCME's range of probe type particulate emission monitors utilise PCME's unique Electrodynamic® measurement principle.

 

When the sensing probe is installed in the duct or stack, particles in the air stream interact with the sensing probe and a charge induction effect is analysed from the probe. Distributions in the particle stream result in a frequency charge induction response which is proportional to the concentration of particles.

 

Previous probe technologies, such as Triboelectric, relied on particle collision to created a measured signal. Electrodynamic® systems however, filter out the dc signal caused by particle collision, which makes the quality of measurement unaffected by build up on the probes which would otherwise cause zero or calibration drift.

 

Very low concentrations of particulate found even after the most efficient bag filter can be measured due to this unique Electrodynamic® technique.(<0.1 mg/m3)

 

These sensors are able to function in stacks and ducts up to 4.5 metres and process temperatures up to 800ºC.

 

Electrodynamic® technology also enables the use of patented fully insulated probes, essential for reliable measurement in high humidity applications (after process and spray driers).

  • PCME STACK 990

    Download

    An Electrodynamic probe technology dust monitor that can be operated with either a Mulitcontroller or Interface Module.

     

    The PCME STACK 990 has automatic self checks, built in logging and is fully calibratable to mg/m3.

     

    The system comes with MCERTS & TUV European approval certificates. 

    Download >
  • PCME VIEW 370

    Download

    An Electrodynamic probe technology dust monitor that can be operated with either a Mulitcontroller or Interface Module.

     

    The PCME VIEW 370 has automatic self checks, built in logging and is fully calibratable to mg/m3.

    Download >
  • LEAK ALERT 75

    Download

    An Electrodynamic probe technology dust monitor with integrated control features in the sensor.

     

    The LEAK ALERT 75 has automatic self checks and is calibratable to mg/m3.

     

    The system comes with MCERTS & TUV European approval certificates. 

    Download >
  • LEAK ALERT 73

    Download

    An Electrodynamic probe technology dust leak detector with integrated control features in the sensor.

     

    The LEAK ALERT 73 has manual self checks and outputs a trending 4-20mA signal to alert increases in dust concentration resulting from a filter leak.

    Download >
  • Leak Locate 660

    Download

    An Electrodynamic probe technology leak detector operating with a Mulitcontroller.

     

    Specifically designed to monitor the outlet of each chamber of a bagfilter to identify the relative dust levels through each chamber, highlighting which chamber or compartment contains leaking, faulty or broken bags, giving pre-warning of emissions to maintenance and process personnel.

    Download >
  • BREAK ALARM 10

    Download

    An Electrodynamic probe technology Broken Bag Detector.

     

    The BREAK ALARM 10 triggers an alarm relay when dust concentration rises to a high level, indicating a failed filter.

    Download >
Electrodynamic Probe Technology image

Product Options

Electrodynamic Dust Probes can be used with the following control unit options.

  • Electrodynamic Probe Technology

    Multi-Channel Control Unit

    The Multicontroller allows operation of up to 16 sensors in the one control unit.

  • Electrodynamic Probe Technology

    Single Channel Control Unit

    The Interface Module controls a single sensor.

  • Electrodynamic Probe Technology

    Integrated Control Unit

    In intergrated systems the Control Features are built into the Sensor.

Proud Australasian Distributors for

  • NovatechNovatechOxygen Analyser Systems
  • PCMEPCMEDust / Particulate Monitoring
  • ProcalProcalIn-situ Gas Analysers

Contact Us

Head Office

Ph: (07) 3255 5158

Contact us for further information regarding any of our products using the contact form  here >

 

We have distributors located around Australia and New Zealand - use the location map to find a distributor in your area.  Find a distributor now >

© Group Instrumentation Pty Ltd | Terms & Conditions | Privacy Policy | Site Map | Distributor Login

Web Design Brisbane :: (zero)seven